K-Umts 1.1

This utility uses wvdial ,in order to connect your 3G UMTS "Option" card to your laptop or pcmcia adaptor
Configure section provide password,username and number to dial
You can create a wvdial.config file in /tmp directory with "save config" button
At reboot temp file will be destroyed for safety.
Check on syslog terminal your output connection and have fun with your wireless umts card..:)


-Depends on Kommander
-Depends on WvDial
-Depends on zenity (http://www.pluto.it/files/ildp/lfs/blfs/6.0/gnome/zenity.html)
Foe ubuntu/Kubuntu users try sudo apt-get install zenity

Tested with a Vodafone umts connect card

Be shure to have 3G kernel module and module "Option" both activated..or choose and recompile it
Bind to /dev/ttyUSB0 shoult be automatic when insert the card..if not check your usb modules(no firmware is required now)

I've started to write this application because my kppp died..:(..i think they had upgrade it or upgrade pppd..so i was not able to connect anymore..even with gnome-ppp
WvDial provides a good stable connection..and resolvs my kppp problems..


::..HOW TO USE IT..::

standard kubuntu kernel 2.6.15.27

When u plug a 3g card,for first time,all modules will be upload and usb serial attached to /dev/ttyUSB0 modem device.
I've noticed that wvdial accept(tell me if wrong)only /dev/modem as device.
You can easly create this link by pressing "Modem Link" button ..
Once created link you could put your data to empty txt spaces in the left corner.

-You must know if your provider needs an account with NAME and PASS.Ex.Vodafone(italy)does not an account required..so put everything u want(but put it!or doesn't work)

-In next release a list of international umts number will be inserted.
But now u must know, at buying act,your number to call(normally *99** or *99***1#..depends on provider and CID number)

-Save .config file in /tmp before start connection..if u don't wvdial will fault

-Once saved,active syslog logging(if don't start syslogd)and finally start wvdial to connect..
In 15-20 seconds you will be connected..without specified any private DNS..and u can watch connection from built-in konsole monitor..
If realtime syslog make your memory lower..stop with "STOP" button..this not influence wvdial connection

So this is the fastest way..but i can only check with italian stuff..if u have another provider or country PLEASE..report your impression or here below..tnx

also available,with comment BLOG:http://divilinux.wordpress.com/2007/01/03/k-umts-connector/

K-Umts-1.1rc1

-Added scan system that controls an amount of data in according to your provider-restricted licence..so example:

You have 50MB of traffic x month
Plane to use 2MB x day..and after reaching quote..ppp0 will be disconnected

-Improved all general script and sudo system
-Tnx to paper0k for support script..next release will be available as soon as possible..with MB gesture instead of BYTES..;)


K-Umts-1.1

-Rename project in K-Umts to help internet search(kumts in germany means other..lol)
-Finally the button "modem link" now can recognized if symlink is activated or not


Kumts-1.2

-Improved skin
-Added current ip-address
-Improved link modem..but sometimes you do this manually: ln -s /dev/ttyUSB0 /dev/modem

Kumts-1.1

-Added a total traffic and dropped packets meter


Kumts 1.0-rc1
-Fixed freeze connect button on start connection.Now as soon as you stop wvdial you can re-use button connection again..without restart kumts
-Change graphics to more userfriendly interface,with help tooltips..
-Added last DNS monitor and date pppd was started
-Added clean monitor